Description
Framed and Regular Staple Coils by Cloud Revolution is now available in iVape.Sydney
A Framed Staple coil isn’t too far removed from a regular Staple coil, but there are some major differences. As with the Staple coil, the Framed Staple coil uses a stack of ribbon wire as the core, but that is where the similarities end and the complexities begin. Framed staple coil cores are surrounded by a thick, round wire on each side, which frames the core — hence the name — and gives the coil a wider and thicker profile.
Once the stack of ribbon wire is sandwiched between two thick, round wires, it is then claptonized with thinner wire. Basically, this means wrapping a thinner wire around the core, which is the same process as building a simple Clapton coil. The Clapton process on a thicker core gives this type of RDA coil the look of staples, which is where this coil gets its name. The staples are wide with grooves in between that are meant to capture more juice thereby providing a better vaping experience.
Another upside of having a thick core is the bigger surface area, which improves cloud thickness and flavor — the multiple-wire core also speeds up the firing process. One major drawback, which might render your RDA inadequate, is that the thickness of this coil might prevent it from fitting on your RDA’s post-holes — a clamp-style RDA would fix this problem, however.
This coil is not easy to build and it will require tons of patience and failed attempts, but it’s also one of the best builds out there, with amazing flavor and large, billowing clouds of vapor.
Get the original Cloud Revolution products Now in iVape.Sydney and enjoy!
Specification of Framed and Regular Staple Coils by Cloud Revolution
Framed Staple Coils
Same same, but one less wrap and cheaper to boot!
Coil Specs:
- 28g N80 x2 frame, with 40g N80 ‘Claptoned’ around 5X1 Kanthal Ribbon.
- 5 Wraps with 3mm Internal Diameter
- Single Coil Mode: 0.24 Ohm / Dual Coil: 0.12 Ohm
Staple Coils
Designed to make the jump from subohm tanks to rebuildables that much easier.
Do not add extra wraps on these as they have no frame to keep the ribbon in place, the ribbon stack is prone to collapsing if extra wraps are added.
Coil Specs:
- Core: 8 x 0.3×0.1 N80 Ribbon
- Fuse: 40g N80
- 7 Wraps with 3mm Internal Diameter
- Resistance: Single Coil: 0.4 Ohm / Dual Coil: 0.2 Ohm
Inside the packaging you will receive:
- 2 x Staple or Framed Staple Coils
Designed for High Wattage Regulated Devices or Mechanical Mods that can fire an atomizer with a resistance down to 0.10 ohm.
Caution: This is an advanced user item, always use high drain high amp batteries. Always use an ohm reader to check your coils resistance and to check for shorts. Always take safety into consideration when vaping.
These coils in dual coil mode are Low Resistance Coils, they will initially may be hard to pulse on high wattage regulated devices as the coil is fresh and thus you may need to use a mechanical device to pulse the coils.
More Products from Cloud Revolution
Manufacturer info Here
WARNING: This is an smoking Item. Please use at own risk and always use proper precautions and handling as these are very sensitive to charging characteristics and may explode or burn if not properly handled. Please note that there is an inherent risk with the use of any and all rechargeable batteries in any circumstance. iVape.Sydney are not responsible for any damage, injury, or defect caused by the improper use and/or mishandling of Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable batteries and chargers. Images are for illustration purposes only. Actual color, finish and packaging may vary.
Tim Alexander Dollery –
Amazing